易胜博登录

  • <tr id='tEO7Hy'><strong id='tEO7Hy'></strong><small id='tEO7Hy'></small><button id='tEO7Hy'></button><li id='tEO7Hy'><noscript id='tEO7Hy'><big id='tEO7Hy'></big><dt id='tEO7Hy'></dt></noscript></li></tr><ol id='tEO7Hy'><option id='tEO7Hy'><table id='tEO7Hy'><blockquote id='tEO7Hy'><tbody id='tEO7Hy'></tbody></blockquote></table></option></ol><u id='tEO7Hy'></u><kbd id='tEO7Hy'><kbd id='tEO7Hy'></kbd></kbd>

    <code id='tEO7Hy'><strong id='tEO7Hy'></strong></code>

    <fieldset id='tEO7Hy'></fieldset>
          <span id='tEO7Hy'></span>

              <ins id='tEO7Hy'></ins>
              <acronym id='tEO7Hy'><em id='tEO7Hy'></em><td id='tEO7Hy'><div id='tEO7Hy'></div></td></acronym><address id='tEO7Hy'><big id='tEO7Hy'><big id='tEO7Hy'></big><legend id='tEO7Hy'></legend></big></address>

              <i id='tEO7Hy'><div id='tEO7Hy'><ins id='tEO7Hy'></ins></div></i>
              <i id='tEO7Hy'></i>
            1. <dl id='tEO7Hy'></dl>
              1. <blockquote id='tEO7Hy'><q id='tEO7Hy'><noscript id='tEO7Hy'></noscript><dt id='tEO7Hy'></dt></q></blockquote><noframes id='tEO7Hy'><i id='tEO7Hy'></i>

                LAN


                  2015/12/17 下午 01:28:03        Administrator        General   2 Comments
                LAN Teaming, also known as load balancing and failover (LBFO), allows multiple network adapters on a computer to be placed into a team for the following purposes:
                • Bandwidth aggregation
                • Traffic failover to prevent connectivity loss in the event of a network component failure

                1. Install OS and LAN drivers .
                2. After entering the OS, go to Device Manager and right click on Network adaptors to configure Network Connection Properties.


                3. Under the Teaming tab, Select “Team with other adapters” and press New Team.


                4. Specify the name for the team.


                5. Select the adapters to include in this team.


                6. Select a team mode. Here Adaptive Load Balancing is chosen.


                7. Finally, the wizard has the settings needed to create the team, and selected network adapters will be shown as a team in the device manager.


                2 Comments
                • Commented on 2016/1/4 下午 04:51:39

                  If other LAN vendor (ex: Realtek) also has teaming feature, may I also follow the same setup procedure to active teaming feature?

                • Commented on 2016/1/26 下午 06:18:15

                  For REALTEK solution, you have to download the "Realtek Ethernet Diagnostic Utility" and install it step by step. Then click "Teaming" in the middle of the Realtek Ethernet Diagnostic Utility window and click the "Create Team" button.

                Post Reply